Show us your hitch!!!!
#21
Re: Show us your hitch!!!!
Let me clarify. I moved the muffler (per the instructions) so my torque wrench would fit and I could be sure I was imparting the specified minimum (72 ft-lbs) on the fastener. Yes, its possible to get to the nut with the muffler hanger attached. The two "tricks" I found worked well were: 1) fishing the bolt leader wires 'backwards' and then attaching the bolt to pull them through to the holes, and 2) installing both vertical bolts and nuts - to locate the hitch before trying to fish the wires for the four remaining horizontal bolts.
#23
Re: Show us your hitch!!!!
Originally Posted by WaltPA
Well, I got my hitch installed today.
I bought a Draw-Tite model #75281. It clears both the refrigerant lines and the muffler by over an inch. After reading some bad stuff, I was worried about both of those.
It took about an 1.5 hours to install, but I was taking my time. I found that with the MMH, both frame ends were 1/2 open. That eliminated the need to drill an access hole on the driver's side. Because of the 1/2 open frame, I inserted the "fishing wire" the thru the bolt hole, and fished it back to the larger target of the open frame end. Because of doing it that way, though much easier (a larger hole as target), the "fishing wire" was about 6" too short. So, I had to extend it by duct taping an extension wire onto its end.
I haven't done lights yet. I bought the Valley T-connector #30131 to attach to the tail lights, and the Modulite #18193 power adapter due to the Message Center's monitoring of power to sense bulb outage. I am not too worried about the lights because my primary usage of the hitch is for a bicycle carrier.
I got all my stuff from etrailer.com.
| (corrected T-connector P/N)
I bought a Draw-Tite model #75281. It clears both the refrigerant lines and the muffler by over an inch. After reading some bad stuff, I was worried about both of those.
It took about an 1.5 hours to install, but I was taking my time. I found that with the MMH, both frame ends were 1/2 open. That eliminated the need to drill an access hole on the driver's side. Because of the 1/2 open frame, I inserted the "fishing wire" the thru the bolt hole, and fished it back to the larger target of the open frame end. Because of doing it that way, though much easier (a larger hole as target), the "fishing wire" was about 6" too short. So, I had to extend it by duct taping an extension wire onto its end.
I haven't done lights yet. I bought the Valley T-connector #30131 to attach to the tail lights, and the Modulite #18193 power adapter due to the Message Center's monitoring of power to sense bulb outage. I am not too worried about the lights because my primary usage of the hitch is for a bicycle carrier.
I got all my stuff from etrailer.com.
| (corrected T-connector P/N)
Thanks
#24
Re: Show us your hitch!!!!
O Oral -
Didn't your Draw-Tite come with rectangular black washers with the square holes that accept the square headed bolts ? See this photo: https://www.greenhybrid.com/share/image2059.html
This would preclude having to enlarge any holes.
Didn't your Draw-Tite come with rectangular black washers with the square holes that accept the square headed bolts ? See this photo: https://www.greenhybrid.com/share/image2059.html
This would preclude having to enlarge any holes.
#25
Re: Show us your hitch!!!!
Originally Posted by glennb
O Oral -
Didn't your Draw-Tite come with rectangular black washers with the square holes that accept the square headed bolts ? See this photo: https://www.greenhybrid.com/share/image2059.html
This would preclude having to enlarge any holes.
Didn't your Draw-Tite come with rectangular black washers with the square holes that accept the square headed bolts ? See this photo: https://www.greenhybrid.com/share/image2059.html
This would preclude having to enlarge any holes.
#26
Re: Show us your hitch!!!!
I'm getting in on this one late, but can't resist congratulating you on your upcoming April Fools Day event. I often tell people that there are only two important events in life. The first is the arrival of the first child, when you learn that you can no longer go out on an impulse, to dinner or a flic or whatever. The second is when that first child becomes old enough to sit for the others, and then you can again go out on an impulse. The years between just fly by.
I have a Draw-Tite, and it is just fine. The fact that the frame stringers were half-open in back made all the difference. On my old Explorer I had to do some heavy drilling.
Hal
(Oops, forgot to enclose quote, showing that the baby comments were directed to Shannon.)
I have a Draw-Tite, and it is just fine. The fact that the frame stringers were half-open in back made all the difference. On my old Explorer I had to do some heavy drilling.
Hal
(Oops, forgot to enclose quote, showing that the baby comments were directed to Shannon.)
#27
Re: Show us your hitch!!!!
Originally Posted by ooral
The horizontal holes in the frame needed to be enlarged some to get the bolts' square heads. I spent most of the time to get the bolt that I have lost in the frame.
Yea, I was worried about loosing a bolt or plate in the frame. It would had been very difficult to pick up the SUV, and shake it out.
#28
Re: Show us your hitch!!!!
Tim - your instincts are correct, they are commonly called "load spreaders" and they are frequently specified on surfaces (like the inside of the frame tube) that are uneven or have raised welds, etc. - to avoid stress concentrations around holes. [ A frame should never have a square hole to accept a square head bolt -- creates stress concentrations in the corners ]
Walt - I assume every DIY'er has a flexible magnetic pick-up (for example: http://allmagnetics.com/hardware/pickuptools.htm) for those frequent times that items are dropped into inaccessible holes. I predicted I would need mine for the hitch install....but I lucked out and fished all six bolts without incident.
Walt - I assume every DIY'er has a flexible magnetic pick-up (for example: http://allmagnetics.com/hardware/pickuptools.htm) for those frequent times that items are dropped into inaccessible holes. I predicted I would need mine for the hitch install....but I lucked out and fished all six bolts without incident.
#29
Re: Show us your hitch!!!!
Originally Posted by glennb
O Oral -
Didn't your Draw-Tite come with rectangular black washers with the square holes that accept the square headed bolts ? See this photo: https://www.greenhybrid.com/share/image2059.html
This would preclude having to enlarge any holes.
Didn't your Draw-Tite come with rectangular black washers with the square holes that accept the square headed bolts ? See this photo: https://www.greenhybrid.com/share/image2059.html
This would preclude having to enlarge any holes.
All I had to do was enlarge the hole enough so that square end would fit in and don't turn while I am tightening the thing.
#30
Re: Show us your hitch!!!!
Originally Posted by glennb
Tim - your instincts are correct, they are commonly called "load spreaders" and they are frequently specified on surfaces (like the inside of the frame tube) that are uneven or have raised welds, etc. - to avoid stress concentrations around holes. [ A frame should never have a square hole to accept a square head bolt -- creates stress concentrations in the corners ]
Walt - I assume every DIY'er has a flexible magnetic pick-up (for example: http://allmagnetics.com/hardware/pickuptools.htm) for those frequent times that items are dropped into inaccessible holes. I predicted I would need mine for the hitch install....but I lucked out and fished all six bolts without incident.
Walt - I assume every DIY'er has a flexible magnetic pick-up (for example: http://allmagnetics.com/hardware/pickuptools.htm) for those frequent times that items are dropped into inaccessible holes. I predicted I would need mine for the hitch install....but I lucked out and fished all six bolts without incident.